RINGFEDER TNS SV (WITH INTERNAL HUB)

Flexible Jaw Couplings Ringfeder TNS SV (With internal hub)

The Ringfeder TNS SV coupling is a torsionally flexible, puncture proof claw coupling which is particularly suited for use with hydrodynamic high-speed couplings. It compensates for angular, radial and axial shaft misalignments within defined limits. The coupling transmits torque through elastic buffers loaded in shear. These buffers come in Perbunan (Pb), Pb82 as a standard, or polyurethane (Vk), and are connected to each other to form an elastic buffer ring. This buffer ring dampens shocks and torsional vibrations and is resistant to oil. Buffer rings made of Perbunan are electrically conductive. The coupling is suitable for use in every direction of rotation and installation position.

RINGFEDER TNS SV

Elastic claw coupling with inner hub and claw flange.
The intermediate ring can be replaced after shifting a shaft with fitted hub.

Notes Ringfeder Jaw Coupling TNS SV

Standard material for intermediate ring: Pb82
Installed size L must be maintained without fail. Axial displacement e.g. by thermal expansions of the connected shafts, must be taken into account through allowances for value L.
General features
Torsionally flexible, compensate for angular, radial and axial shaft offset
Intermediate rings loaded in compression
Elastomers available in various shore hardness degrees
Suitable for temperatures from –30°C to +100°C
Coupling outer diameter up to 400 mm, flange outer diameter 690mm.
Bores up to max. 160 mm
Torques with intermediate ring VkR up to TKn = 8,900 Nm / TKmax = 26,700 Nm
Speeds up to nmax = 7,250 rpm
Flange design short version.

INTRODUCTION
The rotationally resilient coupling of the RINGFEDER TNS SV coupling is flexible in all directions and therefore compensates for angular, parallel and axial shaft misalignments of the connected machines. Misalignments can be caused, for example, by inaccurate assembly, heat movements or settling phenomena.

Elastic intermediate ring
With the RINGFEDER TNS coupling, the torque is transmitted via a compressed elastic intermediate ring. The elastic intermediate ring absorbs shocks and torsional vibrations, is resistant to oil and largely insensitive to temperature.
The strength of different elastomer materials is indicated by their Shore hardness. Elastomers of different strengths are colour-coded for identification. Further details concerning the strength and load capacity are available on request in the technical data sheet.

Elastomer Materials
The elastic intermediate rings of RINGFEDER TNS SV are made of butadiene-nitril-rubber (Pb82) or polyurethane (VkR). The black buffer (Pb82) are normally electrically conductive and therefore prevent undesirable electrostatic charges. The red (VkR) ring ensure electrical insulation between connected machines as long as there are no other electrically conductive connections. The resilience of the individual elastomer materials is designated by their Shore hardness. From these values an indirect conclusion can be drawn with respect to the torques the coupling is able to transmit and its spring stiffness. For further details, please see the technical data sheet.

Avoiding Torsional Vibration
By virtue of the rotational resilience of the coupling, dangerous torsional vibrations from the operational range of plant machinery can be transferred to rotational speed ranges in which no negative effects are to be expected. The elastic intermediate rings possess a high material damping capability which makes it possible for the couplings to keep the resonance enhancements within limits when passing through dangerous speed ranges, thereby protecting the coupled machines against damage. The couplings also mitigate torque shocks and cause a vibrating system that has been excited by an impact to come to rest very quickly due to the material damping qualities. The conduction of structure-borne noise is prevented.

Environmental conditions
The employed elastomer materials operate reliably in ambient temperature ranges of –30° to +100°C. Please contact RINGFEDER POWER TRANS­MISSION if higher ambient temperatures are involved. The influence of the temperature on the coupling size selection is explained in more detail in the below-mentioned design directives. It is only allowed to operate the coupling in normal industrial air. Aggressive media may attack the coupling components, bolts and elastic elements, and, therefore, present a danger to the operational safety of the coupling. The coupling can be declared compliant with the European Directive 2014/34/EU (ATEX). Please contact RINGFEDER POWER TRANSMISSION regarding the declaration of conformity according to 2014/34/EU and the effects of aggressive ambient media.

Download catalogue Ringfeder TNS SV (WITH INTERNAL HUB): 

Download Installation Instruction Ringfeder TNS SV (WITH INTERNAL HUB): 

Size	TKN [Nm]	Dimension [mm]
		d1 Max	d1 Max	DPC7	D1	L
100	70	27	145	128	105	42
125	128	34	170	148	126	47
145	220	42	194	172	145	55
170	340	58	220	195	170	60
200	590	65	250	228	200	65
230	900	70	290	265	230	70
260	1400	90	335	310	260	85.5
300	2090	105	385	360	300	100
360	3450	140	455	420	360	123
360	3450	140	514	480	360	125
400	4750	160	514	480	400	125
RELATED PRODUCTS Flexible Jaw couplings Ringfeder TNS S-St Flexible Jaw couplings Ringfeder TNS S-LSt Ringfeder TNS SDD-5 (REMOVABLE CLAW RINGS, SHORT HUBS) Ringfeder TNS SDDL-5 (REMOVABLE CLAW RINGS, LONG HUBS) Ringfeder TNS S-BT (WITH BRAKE DRUM) Ringfeder TNS SDDL-5-BS (REMOVABLE CLAW RINGS, BRAKE DISK, LONG HUB) Ringfeder TNS SDDL-5-BSV (REMOVABLE CLAW RINGS, INTERNALLY VENTILATED BRAKE DISK,… Ringfeder TNS SX (SHORT HUB)